A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
What're your thoughts about A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily easily accessible, the task can move immediately; if you have to open a wall to get rid of the old tub and place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's abilities, although you will need an assistant to leave the old tub and also embeded in the brand-new one. Make certain you have actually qualified on your own for the work as well as are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to think about utilizing one before you start. Opportunities are you may need an expert plumber to make tube links.
This article will assist you mount a brand-new bath tub in your washroom if you have actually currently acquired a new bathtub as well as do not require to transform the setup of your previous water supply pipes.
Your devices and product list ought to make up the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The procedure of removing the existing taps can be quite problematic because of the limited accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Prior to moving on to fit the new faucets, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers are in area in between the tap and the sink. Secure the faucet in place with the supplier offered backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type needs to be linked to the faucet finishes initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wood boards under its feet, place the bathtub in the needed setting. The wood boards are useful in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little factors.
The following goal is to make certain that the tub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the bath tub up until the spirit level reads level.
To mount taps, fit all-time low of the outermost versatile tap port to the appropriate supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water system and inspect all joints as well as new pipework for leaks and also tighten them if needed. Load the bathtub as well as likewise examine the overflow outlet and the regular electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's user's manual. Tiling and also securing around the bath tub ought to wait up until the tub has actually been made use of at least once as this will certainly resolve it right into its final setting.
Preparing for the Installment
To start with, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to stop stress on the bathtub.
Fit the adaptable tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath as well as the tiling, causing complications with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can split rather early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly available on the market. It is suggested to fit the floor tiles making use of water-resistant or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our piece on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking the time to read through our blog post. Sharing is good. Who knows, you could be helping someone out. I enjoy reading our article about How to Install a Bathtub.
Free Quote Report this page